Clean Lines on Ricoh Sublimation Printer

There are rare Ricoh Sublimation printer users, but they do face some issues while printing on a regular basis. Some complaints are about the lines that are formed on the print output in most cases.

In case you face a horizontal line issue or see any type of lines on your final output, it is possible that you are facing this issue based on various problems. But don’t worry, it’s not a major issue.

In this guide, I will show you how to clean lines on the Ricoh sublimation printer, along with other small problems that are commonly found with printers.

How to Clean Lines on Ricoh Sublimation Printer?

For me, I did try a lot of ways to fix this issue, but the lines were not going anywhere. So I realized I had set my print area to the maximum in the printer driver before. You will have to check this setting you’re your printer.

Returning it to its original state that is set as default by the manufacturer will fix everything for you as it did for me. So this is the best and most basic way to remove lines from a print formed by a Ricoh sublimation printer.

What are the horizontal banding lines on paper when you print with a sublimation printer?

Horizontal banding refers to the lines that are commonly left in the path of printhead motion. It’s a rather typical issue for which many individuals don’t have an instant remedy.

Pinstripes on a shirt or the flashing of an outdated CRT display might be mistaken for them. These lines, whatever name you give them, are not acceptable on your print. To fix such issues, you have to reset your printer settings to default.

Other ways to fix such issues are:

  • Run a head cleaning cycle if you detect line breaks in the nozzle check.
  • Aside from a blocked printhead nozzle or a mismatched printhead, the most typical cause of banding is erroneous media typesetting.
  • Print a small test print to see if the horizontal banding remains. Make sure you’re using the right ICC profile and media type setting in your print settings.
  • Nozzle inspections may provide a lot of information for which you will have to take a careful look.
  • If all lines are solid, calculate how long it has been since the printhead was aligned. I usually conduct a printhead alignment every 6-12 months, depending on printer usage.
  • That should be your next move if you’re outside this timeframe.

Common Issues with Printers:

There are various issues with different models of printers, but there is always a solution to the problem. It’s best to get guidance directly from the manufacturer if you’re having printhead problems.

The methods below will work for most brands if there is an issue with the printhead; however, it’s vital to verify first.

Clogging in the Nozzles:

Your printer’s print cleaning cycle works a little like a self-cleaning oven: if you’re lucky, it can solve the problem on its own, but more often than not, it requires your help.

The print cleaning cycle might assist in eliminating air obstructions that are causing problems with your printer. It’s vital to remember that running more than three print cleaning processes at once might lead to ink accumulation in the printhead nozzles.

The Buildup of Dried ink on the Printhead:

If the print cleaning cycle fails, dried ink might be at blame. To remove any accumulation, remove the printhead and rinse the nozzles neat and tidy.

This may be tough based on your printer type; some printheads are more difficult to extract than others.

Dust in Printer:

Dust can accumulate within the printer, exacerbating any issues with clogged nozzles. You should vacuum your printer on a regular basis to avoid printhead troubles caused by dust build-up.

You should clean at the absolute least if you’re having printing problems. Dust with an airbrush or a vacuum accessory rather than rags or paper towels which can leave fur behind.

The Printer Is Never Turned Off:

One of the most prevalent issues with printers is that they are left on all the time. When you switch on a printer, it goes through a fast cleaning cycle.

If you don’t turn it off, it doesn’t get the chance to perform this cycle every day. So at the end of the day, switch off your printer and put it back on in the morning.

Your Printer Gets Low Use:

Because blocked printer nozzles are the source of many printhead troubles, you must prevent them from clogging by operating your printer on a regular basis.

Regular usage also eliminates negative air pressure and dust accumulation, so you’re avoiding three printhead concerns in one easy move.

What’s the deal with my printer leaving lines?

The printer heads may be out of alignment if you see streaks and unsightly lines. The printer’s control panel has an alignment tool.

If that isn’t the case, the printer is probably unclean. Ink lines on the edges of the paper indicate that there is ink on the sheets and other elements of the printer.

This was a discussion on cleaning lines that are formed by printing through sublimation printers. The easy answers have been shared, and I hope you found your solution.

Also check:


Why do my sublimation prints have white lines?

Because of a clogged printer head, white lines will begin to show on your printouts. It’s best to avoid running many cleaning procedures one after the other since this will just jam the printer head with ink.

Similar Posts

Leave a Reply